How to install PPF on a Honda Civic Sedan (2025+)

1. Check it is your car

Kits follow the body shape, not the model year. These kits are for the Honda Civic Sedan (2025+, eleventh gen refresh):

• New front fascia with a larger, body-colour-framed lower opening
• Three front bumper patterns: LX / Sport (petrol), Si / Sport Hybrid (the hybrid carries the Si-style lower fascia), and Sport Touring Hybrid (with front parking sensors)
• Si has its own rocker panels; every trim shares the rear bumper (no rear sensors)
• Same slim headlights as 2022; no factory fog lamps on any 2025+ trim
• Not for: Civic Type R (wide body)
• Not for: Hatchback body

Not sure? Compare every Honda Civic body or use Find my fit.

2. Choose how much to cover

• Full Front PPF Kit

  Everything that takes stone chips on the highway. The most popular choice.

  Covers: Full hood, front bumper, both fenders, mirror caps, headlamps and grille.

  from≈$620USDSee the kit

• Partial Hood, Fender & Mirror PPF Kit

  The leading edge of the hood and fenders plus the mirror caps: chip protection on a budget.

  Covers: Partial hood (leading edge), both fenders (partial) and mirror caps.

  from≈$291USDSee the kit

• Rocker Panel PPF Kit

  The lower sides that collect grit and road salt. Small pieces, a good first install.

  Covers: Rocker panels.

  from≈$277USDSee the kit

• Full Body PPF Kit

  Every painted panel as one numbered set.

  Covers: Full hood, front bumper, both fenders, mirror caps, headlamps, A-pillars, front doors, rear doors, rocker panels, rear quarters, grille, roof, door edges, door handle cups, rear bumper, trunk lid and trunk ledge / loading edge.

  from≈$1,788USDSee the kit

All 27 kits for the Honda Civic Sedan (2025+), including single panels.

3. Pick your car’s options before ordering

On the kit page you tell us how your Honda Civic Sedan (2025+) is equipped, and the pieces are cut to match. Check your car for:

Front parking sensors

With front parking sensors (cut-outs included) · Without front parking sensors

Roof type

Solid roof (no opening) · Single sunroof / moonroof opening (cut-out included) · Panoramic or dual-pane glass roof (only the painted edges are covered)

Rear spoiler

No spoiler · With spoiler

4. What you need

• A clean, sheltered place to work
• The supplied pre-cut film and numbered map
• Soft squeegee and clean microfibre cloths
• Two clean spray bottles for slip and tack solution (not included)

The kit includes the squeegee, a microfibre cloth and installation solution to mix with water.

5. Apply the film

1. 1Clean the panel. Wash and decontaminate the paint so no dirt gets trapped under the film. Work in a clean, sheltered space.
2. 2Prepare your solutions. Mix the supplied installation solution with water as its label directs. Keep slip and tack solution in separate labelled spray bottles.
3. 3Wet the panel and film. Spray the panel, your hands and the adhesive side of the pre-cut piece. The film should be able to float into position.
4. 4Match the numbered map. Use the installation map and panel edges to align each piece before pressing it down.
5. 5Squeegee out the water. Anchor the centre, then work outwards in overlapping strokes. Lift and re-wet a section if it traps water or air.
6. 6Finish the edges. Use tack solution where the supplied guide calls for it, then squeegee the edges. Let the film settle before washing the car.

• Start small. If it is your first time, do the mirror caps or rocker panels first to get a feel for floating and squeegeeing the film.
• Line up the cut-outs first. On a bumper with sensor or camera openings, float the piece until every opening sits over its sensor before you squeegee.
• Follow the numbers. Each piece is numbered to the installation map in your kit, so you always know where it goes.

Full installation and removal guide, with photos.